New upstream version 1.42.8 upstream/1.42.8

1 files changed, 2 insertions, 1 deletions

diff --git a/src/libnmc-setting/settings-docs.h b/src/libnmc-setting/settings-docs.h
index c10ece6a..0b2f8eca 100644
--- a/src/libnmc-setting/settings-docs.h
+++ b/src/libnmc-setting/settings-docs.h
@@ -153,7 +153,7 @@
 #define DESCRIBE_DOC_NM_SETTING_GSM_USERNAME N_("The username used to authenticate with the network, if required.  Many providers do not require a username, or accept any username.  But if a username is required, it is specified here.")
 #define DESCRIBE_DOC_NM_SETTING_INFINIBAND_MAC_ADDRESS N_("If specified, this connection will only apply to the IPoIB device whose permanent MAC address matches. This property does not change the MAC address of the device (i.e. MAC spoofing).")
 #define DESCRIBE_DOC_NM_SETTING_INFINIBAND_MTU N_("If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple frames.")
-#define DESCRIBE_DOC_NM_SETTING_INFINIBAND_P_KEY N_("The InfiniBand P_Key to use for this device. A value of -1 means to use the default P_Key (aka \"the P_Key at index 0\"). Otherwise, it is a 16-bit unsigned integer, whose high bit is set if it is a \"full membership\" P_Key.")
+#define DESCRIBE_DOC_NM_SETTING_INFINIBAND_P_KEY N_("The InfiniBand p-key to use for this device. A value of -1 means to use the default p-key (aka \"the p-key at index 0\"). Otherwise, it is a 16-bit unsigned integer, whose high bit 0x8000 is set if it is a \"full membership\" p-key. The values 0 and 0x8000 are not allowed. With the p-key set, the interface name is always \"$parent.$p_key\". Setting \"connection.interface-name\" to another name is not supported. Note that kernel will internally always set the full membership bit, although the interface name does not reflect that. Usually the user would want to configure a full membership p-key with 0x8000 flag set.")
 #define DESCRIBE_DOC_NM_SETTING_INFINIBAND_PARENT N_("The interface name of the parent device of this device. Normally NULL, but if the \"p_key\" property is set, then you must specify the base device by setting either this property or \"mac-address\".")
 #define DESCRIBE_DOC_NM_SETTING_INFINIBAND_TRANSPORT_MODE N_("The IP-over-InfiniBand transport mode. Either \"datagram\" or \"connected\".")
 #define DESCRIBE_DOC_NM_SETTING_IP4_CONFIG_ADDRESSES N_("A list of IPv4 addresses and their prefix length. Multiple addresses can be separated by comma. For example \"192.168.1.5/24, 10.1.0.5/24\". The addresses are listed in decreasing priority, meaning the first address will be the primary address.")
@@ -436,6 +436,7 @@
 #define DESCRIBE_DOC_NM_SETTING_WPAN_PAGE N_("IEEE 802.15.4 channel page. A positive integer or -1, meaning \"do not set, use whatever the device is already set to\".")
 #define DESCRIBE_DOC_NM_SETTING_WPAN_PAN_ID N_("IEEE 802.15.4 Personal Area Network (PAN) identifier.")
 #define DESCRIBE_DOC_NM_SETTING_WPAN_SHORT_ADDRESS N_("Short IEEE 802.15.4 address to be used within a restricted environment.")
+#define DESCRIBE_DOC_NM_SETTING_BOND_PORT_PRIO N_("The port priority for bond active port re-selection during failover. A higher number means a higher priority in selection. The primary port has the highest priority. This option is only compatible with active-backup, balance-tlb and balance-alb modes.")
 #define DESCRIBE_DOC_NM_SETTING_BOND_PORT_QUEUE_ID N_("The queue ID of this bond port. The maximum value of queue ID is the number of TX queues currently active in device.")
 #define DESCRIBE_DOC_NM_SETTING_HOSTNAME_FROM_DHCP N_("Whether the system hostname can be determined from DHCP on this connection. When set to NM_TERNARY_DEFAULT (-1), the value from global configuration is used. If the property doesn't have a value in the global configuration, NetworkManager assumes the value to be NM_TERNARY_TRUE (1).")
 #define DESCRIBE_DOC_NM_SETTING_HOSTNAME_FROM_DNS_LOOKUP N_("Whether the system hostname can be determined from reverse DNS lookup of addresses on this device. When set to NM_TERNARY_DEFAULT (-1), the value from global configuration is used. If the property doesn't have a value in the global configuration, NetworkManager assumes the value to be NM_TERNARY_TRUE (1).")