From d4d8b2b91f7ba000d97a8b2aab48c85000c11314 Mon Sep 17 00:00:00 2001 From: Michael Biebl Date: Wed, 4 Oct 2023 11:44:49 +0200 Subject: New upstream version 1.44.2 --- man/nm-settings-dbus.xml | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'man/nm-settings-dbus.xml') diff --git a/man/nm-settings-dbus.xml b/man/nm-settings-dbus.xml index 9eb902a0..db2f3b12 100644 --- a/man/nm-settings-dbus.xml +++ b/man/nm-settings-dbus.xml @@ -1,6 +1,6 @@ -nm-settings-dbusNetworkManager developersnm-settings-dbus5NetworkManagerConfiguration1.44.0nm-settings-dbusDescription of settings and properties of NetworkManager connection profiles on the D-Bus APIDescription +nm-settings-dbusNetworkManager developersnm-settings-dbus5NetworkManagerConfiguration1.44.2nm-settings-dbusDescription of settings and properties of NetworkManager connection profiles on the D-Bus APIDescription NetworkManager is based on a concept of connection profiles, sometimes referred to as connections only. These connection profiles contain a network configuration. When NetworkManager activates a connection profile on a network device the configuration will @@ -344,7 +344,7 @@ If the table setting is left at zero, it is eligible to be overwritten via globa Policy routing disabled means that NetworkManager will add all routes to the main table (except static routes that explicitly configure a different table). Additionally, NetworkManager will not delete any extraneous routes from tables except the main table. This is to preserve backward compatibility for users who manage routing tables outside of NetworkManager.routesarray of legacy IPv6 route struct (a(ayuayu))Deprecated in favor of the 'route-data' property, but this can be used for backward-compatibility with older daemons. Note that if you send this property the daemon will ignore 'route-data'. Array of IPv6 route structures. Each IPv6 route structure is composed of an IPv6 address, a prefix length (0 - 128), an IPv6 next hop address (which may be zeroed out if there is no next hop), and a metric. If the metric is 0, NM will choose an appropriate default metric for the device.routing-rulesarray of 'a{sv}'Array of dictionaries for routing rules. Each routing rule supports the following options: action (y), dport-end (q), dport-start (q), family (i), from (s), from-len (y), fwmark (u), fwmask (u), iifname (s), invert (b), ipproto (s), oifname (s), priority (u), sport-end (q), sport-start (q), supress-prefixlength (i), table (u), to (s), tos (y), to-len (y), range-end (u), range-start (u).tokenstringConfigure the token for draft-chown-6man-tokenised-ipv6-identifiers-02 IPv6 tokenized interface identifiers. Useful with eui64 addr-gen-mode. -When set, the token is used as IPv6 interface identifier instead of the hardware address. This only applies to addresses from stateless autoconfiguration, not to IPv6 link local addresses.ip-tunnel settingIP Tunneling Settings.Key NameValue TypeDefault ValueValue Descriptionencapsulation-limituint320How many additional levels of encapsulation are permitted to be prepended to packets. This property applies only to IPv6 tunnels. To disable this option, add NM_IP_TUNNEL_FLAG_IP6_IGN_ENCAP_LIMIT (0x1) to ip-tunnel flags.flagsuint320Tunnel flags. Currently, the following values are supported: NM_IP_TUNNEL_FLAG_IP6_IGN_ENCAP_LIMIT (0x1), NM_IP_TUNNEL_FLAG_IP6_USE_ORIG_TCLASS (0x2), NM_IP_TUNNEL_FLAG_IP6_USE_ORIG_FLOWLABEL (0x4), NM_IP_TUNNEL_FLAG_IP6_MIP6_DEV (0x8), NM_IP_TUNNEL_FLAG_IP6_RCV_DSCP_COPY (0x10), NM_IP_TUNNEL_FLAG_IP6_USE_ORIG_FWMARK (0x20). They are valid only for IPv6 tunnels.flow-labeluint320The flow label to assign to tunnel packets. This property applies only to IPv6 tunnels.fwmarkuint320The fwmark value to assign to tunnel packets. This property can be set to a non zero value only on VTI and VTI6 tunnels.input-keystringThe key used for tunnel input packets; the property is valid only for certain tunnel modes (GRE, IP6GRE). If empty, no key is used.localstringThe local endpoint of the tunnel; the value can be empty, otherwise it must contain an IPv4 or IPv6 address.modeuint320The tunneling mode, for example NM_IP_TUNNEL_MODE_IPIP (1) or NM_IP_TUNNEL_MODE_GRE (2).mtuuint320If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple fragments.output-keystringThe key used for tunnel output packets; the property is valid only for certain tunnel modes (GRE, IP6GRE). If empty, no key is used.parentstringIf given, specifies the parent interface name or parent connection UUID the new device will be bound to so that tunneled packets will only be routed via that interface.path-mtu-discoverybooleanTRUEWhether to enable Path MTU Discovery on this tunnel.remotestringThe remote endpoint of the tunnel; the value must contain an IPv4 or IPv6 address.tosuint320The type of service (IPv4) or traffic class (IPv6) field to be set on tunneled packets.ttluint320The TTL to assign to tunneled packets. 0 is a special value meaning that packets inherit the TTL value.macsec settingMACSec Settings.Key NameValue TypeDefault ValueValue DescriptionencryptbooleanTRUEWhether the transmitted traffic must be encrypted.mka-cakstringThe pre-shared CAK (Connectivity Association Key) for MACsec Key Agreement. Must be a string of 32 hexadecimal characters.mka-cak-flagsNMSettingSecretFlags (uint32)Flags indicating how to handle the "mka-cak" property.mka-cknstringThe pre-shared CKN (Connectivity-association Key Name) for MACsec Key Agreement. Must be a string of hexadecimal characters with a even length between 2 and 64.modeint320Specifies how the CAK (Connectivity Association Key) for MKA (MACsec Key Agreement) is obtained.parentstringIf given, specifies the parent interface name or parent connection UUID from which this MACSEC interface should be created. If this property is not specified, the connection must contain an "802-3-ethernet" setting with a "mac-address" property.portint321The port component of the SCI (Secure Channel Identifier), between 1 and 65534.send-scibooleanTRUESpecifies whether the SCI (Secure Channel Identifier) is included in every packet.validationint322Specifies the validation mode for incoming frames.macvlan settingMAC VLAN Settings.Key NameValue TypeDefault ValueValue Descriptionmodeuint320The macvlan mode, which specifies the communication mechanism between multiple macvlans on the same lower device.parentstringIf given, specifies the parent interface name or parent connection UUID from which this MAC-VLAN interface should be created. If this property is not specified, the connection must contain an "802-3-ethernet" setting with a "mac-address" property.promiscuousbooleanTRUEWhether the interface should be put in promiscuous mode.tapbooleanFALSEWhether the interface should be a MACVTAP.match settingMatch settings.Key NameValue TypeDefault ValueValue Descriptiondriverarray of stringA list of driver names to match. Each element is a shell wildcard pattern. +When set, the token is used as IPv6 interface identifier instead of the hardware address. This only applies to addresses from stateless autoconfiguration, not to IPv6 link local addresses.ip-tunnel settingIP Tunneling Settings.Key NameValue TypeDefault ValueValue Descriptionencapsulation-limituint320How many additional levels of encapsulation are permitted to be prepended to packets. This property applies only to IPv6 tunnels. To disable this option, add NM_IP_TUNNEL_FLAG_IP6_IGN_ENCAP_LIMIT (0x1) to ip-tunnel flags.flagsuint320Tunnel flags. Currently, the following values are supported: NM_IP_TUNNEL_FLAG_IP6_IGN_ENCAP_LIMIT (0x1), NM_IP_TUNNEL_FLAG_IP6_USE_ORIG_TCLASS (0x2), NM_IP_TUNNEL_FLAG_IP6_USE_ORIG_FLOWLABEL (0x4), NM_IP_TUNNEL_FLAG_IP6_MIP6_DEV (0x8), NM_IP_TUNNEL_FLAG_IP6_RCV_DSCP_COPY (0x10), NM_IP_TUNNEL_FLAG_IP6_USE_ORIG_FWMARK (0x20). They are valid only for IPv6 tunnels.flow-labeluint320The flow label to assign to tunnel packets. This property applies only to IPv6 tunnels.fwmarkuint320The fwmark value to assign to tunnel packets. This property can be set to a non zero value only on VTI and VTI6 tunnels.input-keystringThe key used for tunnel input packets; the property is valid only for certain tunnel modes (GRE, IP6GRE). If empty, no key is used.localstringThe local endpoint of the tunnel; the value can be empty, otherwise it must contain an IPv4 or IPv6 address.modeuint320The tunneling mode. Valid values: NM_IP_TUNNEL_MODE_IPIP (1), NM_IP_TUNNEL_MODE_GRE (2), NM_IP_TUNNEL_MODE_SIT (3), NM_IP_TUNNEL_MODE_ISATAP (4), NM_IP_TUNNEL_MODE_VTI (5), NM_IP_TUNNEL_MODE_IP6IP6 (6), NM_IP_TUNNEL_MODE_IPIP6 (7), NM_IP_TUNNEL_MODE_IP6GRE (8), NM_IP_TUNNEL_MODE_VTI6 (9), NM_IP_TUNNEL_MODE_GRETAP (10) and NM_IP_TUNNEL_MODE_IP6GRETAP (11)mtuuint320If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple fragments.output-keystringThe key used for tunnel output packets; the property is valid only for certain tunnel modes (GRE, IP6GRE). If empty, no key is used.parentstringIf given, specifies the parent interface name or parent connection UUID the new device will be bound to so that tunneled packets will only be routed via that interface.path-mtu-discoverybooleanTRUEWhether to enable Path MTU Discovery on this tunnel.remotestringThe remote endpoint of the tunnel; the value must contain an IPv4 or IPv6 address.tosuint320The type of service (IPv4) or traffic class (IPv6) field to be set on tunneled packets.ttluint320The TTL to assign to tunneled packets. 0 is a special value meaning that packets inherit the TTL value.macsec settingMACSec Settings.Key NameValue TypeDefault ValueValue DescriptionencryptbooleanTRUEWhether the transmitted traffic must be encrypted.mka-cakstringThe pre-shared CAK (Connectivity Association Key) for MACsec Key Agreement. Must be a string of 32 hexadecimal characters.mka-cak-flagsNMSettingSecretFlags (uint32)Flags indicating how to handle the "mka-cak" property.mka-cknstringThe pre-shared CKN (Connectivity-association Key Name) for MACsec Key Agreement. Must be a string of hexadecimal characters with a even length between 2 and 64.modeint320Specifies how the CAK (Connectivity Association Key) for MKA (MACsec Key Agreement) is obtained.parentstringIf given, specifies the parent interface name or parent connection UUID from which this MACSEC interface should be created. If this property is not specified, the connection must contain an "802-3-ethernet" setting with a "mac-address" property.portint321The port component of the SCI (Secure Channel Identifier), between 1 and 65534.send-scibooleanTRUESpecifies whether the SCI (Secure Channel Identifier) is included in every packet.validationint322Specifies the validation mode for incoming frames.macvlan settingMAC VLAN Settings.Key NameValue TypeDefault ValueValue Descriptionmodeuint320The macvlan mode, which specifies the communication mechanism between multiple macvlans on the same lower device.parentstringIf given, specifies the parent interface name or parent connection UUID from which this MAC-VLAN interface should be created. If this property is not specified, the connection must contain an "802-3-ethernet" setting with a "mac-address" property.promiscuousbooleanTRUEWhether the interface should be put in promiscuous mode.tapbooleanFALSEWhether the interface should be a MACVTAP.match settingMatch settings.Key NameValue TypeDefault ValueValue Descriptiondriverarray of stringA list of driver names to match. Each element is a shell wildcard pattern. See NMSettingMatch:interface-name for how special characters '|', '&', '!' and '\\' are used for optional and mandatory matches and inverting the pattern.interface-namearray of stringA list of interface names to match. Each element is a shell wildcard pattern. -- cgit 1.3.0-6-gf8a5