NetworkManager.conf: NetworkManager Reference Manual

-

Description

-

NetworkManager.conf is the configuration file for NetworkManager. It is used - to set up various aspects of NetworkManager's behavior. The - location of the main file and configuration directories may be changed - through use of the --config, --config-dir, - --system-config-dir, and --intern-config - argument for NetworkManager, respectively. -

-

If a default NetworkManager.conf is - provided by your distribution's packages, you should not modify - it, since your changes may get overwritten by package - updates. Instead, you can add additional .conf - files to the /etc/NetworkManager/conf.d directory. - These will be read in order, with later files overriding earlier ones. - Packages might install further configuration snippets to /usr/lib/NetworkManager/conf.d. - This directory is parsed first, even before NetworkManager.conf. - Scripts can also put per-boot configuration into /run/NetworkManager/conf.d. - This directory is parsed second, also before NetworkManager.conf. - The loading of a file /run/NetworkManager/conf.d/name.conf - can be prevented by adding a file /etc/NetworkManager/conf.d/name.conf. - Likewise, a file /usr/lib/NetworkManager/conf.d/name.conf - can be shadowed by putting a file of the same name to either /etc/NetworkManager/conf.d - or /run/NetworkManager/conf.d. -

-

- NetworkManager can overwrite certain user configuration options via D-Bus or other internal - operations. In this case it writes those changes to /var/lib/NetworkManager/NetworkManager-intern.conf. - This file is not intended to be modified by the user, but it is read last and can shadow - user configuration from NetworkManager.conf. -

-

- Certain settings from the configuration can be reloaded at runtime either by sending SIGHUP signal or via - D-Bus' Reload call. -

-

- NetworkManager does not require any configuration in NetworkManager.conf. Depending - on your use case, you may remove all files to restore the default configuration (factory reset). But - note that your distribution or other packages may drop configuration snippets for NetworkManager, such - that they are part of the factory default. -

-

File Format

-

- The configuration file format is so-called key file (sort of - ini-style format). It consists of sections (groups) of - key-value pairs. Lines beginning with a '#' and blank lines are - considered comments. Sections are started by a header line - containing the section enclosed in '[' and ']', and ended - implicitly by the start of the next section or the end of the - file. Each key-value pair must be contained in a section. -

-

- For keys that take a list of devices as their value, you can - specify devices by their MAC addresses or interface names, or - "*" to specify all devices. See the section called “Device List Format” - below. -

-

- A simple configuration file looks like this: -

-

-[main]
-plugins=keyfile
-

-

- As an extension to the normal keyfile format, you can also - append a value to a previously-set list-valued key by doing: -

-

-plugins+=another-plugin
-plugins-=remove-me
-

-

-`main` section

-

---- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

`plugins`	- - Lists system settings plugin names separated by ','. These - plugins are used to read and write system-wide - connection profiles. When multiple plugins are specified, the - connections are read from all listed plugins. When writing - connections, the plugins will be asked to save the - connection in the order listed here; if the first plugin - cannot write out that connection type (or can't write out - any connections) the next plugin is tried, etc. If none of - the plugins can save the connection, an error is returned - to the user. - - - The default value and the number of available plugins is - distro-specific. See the section called “Plugins” - below for the available plugins. - Note that NetworkManager's native `keyfile` - plugin is always appended to the end of this list (if it doesn't - already appear earlier in the list). - -
`monitor-connection-files`	This setting is deprecated and has no effect. Profiles - from disk are never automatically reloaded. Use for example `nmcli connection (re)load` - for that.
`auth-polkit`	Whether the system uses PolicyKit for authorization. - If `true`, non-root requests are authorized using PolicyKit. - Requests from root (user ID zero) are always granted without asking PolicyKit. - If `false`, all requests will be allowed and PolicyKit is - not used. If set to `root-only` PolicyKit is not used and - all requests except root are denied. - The default value is `true`. -
`dhcp`	- This key sets up what DHCP client - NetworkManager will use. Allowed values depend on build configuration and - typically include `internal` and `dhcpcd`. - Support for unmaintained `dhclient` client has been deprecated - and disabled by default. - The `internal` client is built-in, while other options - may require an external DHCP client to be installed. - If this key is missing, `internal` - is used with a fallback to other suppored clients in this order: - `internal`, `dhcpcd`, - `dhclient`. -
`no-auto-default`	- Specify devices for which - NetworkManager shouldn't create default wired connection - (Auto eth0). By default, NetworkManager creates a temporary - wired connection for any Ethernet device that is managed and - doesn't have a connection configured. List a device in this - option to inhibit creating the default connection for the - device. May have the special value `` to - apply to all devices. - When the default wired connection is deleted or saved - to a new persistent connection by a plugin, the device is - added to a list in the file - `/var/lib/NetworkManager/no-auto-default.state` - to prevent creating the default connection for that device - again. - See the section called “Device List Format” for the syntax how to - specify a device. - - - Example: - - -no-auto-default=00:22:68:5c:5d:c4,00:1e:65:ff:aa:ee -no-auto-default=eth0,eth1 -no-auto-default= - - - -
`ignore-carrier`	- This setting is deprecated for the per-device setting - `ignore-carrier` which overwrites this setting - if specified (See `ignore-carrier`). - Otherwise, it is a list of matches to specify for which device - carrier should be ignored. See the section called “Device List Format” for the - syntax how to specify a device. Note that controller types like - bond, bridge, and team ignore carrier by default. You can however - revert that default using the "except:" specifier (or better, - use the per-device setting instead of the deprecated setting). -
`assume-ipv6ll-only`	- - Specify devices for which NetworkManager will try to - generate a connection based on initial configuration when - the device only has an IPv6 link-local address. - - See the section called “Device List Format” for the syntax how to - specify a device. - -
`configure-and-quit`	- - This option is no longer useful to configure in NetworkManager.conf file. - It can however also be configured on the command line with the same - values, where it has some use. - - - When set to '`initrd`', NetworkManager does not connect - to D-Bus and quits after configuring the network. This is an implementation - detail how the NetworkManager module of dracut can run NetworkManager. - An alternative to this is having NetworkManager as a systemd service - with D-Bus in initrd. - - - The value '`true`' is unsupported since version 1.36. - Previously this was a mode where NetworkManager would quit after configuring - the network and run helper processes for DHCP and SLAAC. - - - Otherwise, NetworkManager runs a system service with D-Bus and does not - quit during normal operation. - -
`hostname-mode`	- - Set the management mode of the hostname. This parameter will - affect only the transient hostname. If a valid static hostname is set, - NetworkManager will skip the update of the hostname despite the value of - this option. An hostname empty or equal to 'localhost', 'localhost6', - 'localhost.localdomain' or 'localhost6.localdomain' is considered invalid. - - `default`: NetworkManager will update the - hostname with the one provided via DHCP or reverse DNS lookup of the - IP address on the connection with the default route or on any - connection with the property hostname.only-from-default set to - '`false`'. Connections are considered in order of - increasing value of the `hostname.priority` - property. In case multiple connections have the same priority, - connections activated earlier are considered first. If no hostname can - be determined in such way, the hostname will be updated to the last - one set outside NetworkManager or to 'localhost.localdomain'. - - `dhcp`: this is similar to - '`default`', with the difference that after trying to - get the DHCP hostname, reverse DNS lookup is not done. Note that - selecting this option is equivalent to setting the property - '`hostname.from-dns-lookup`' to - '`false`' globally for all connections in - NetworkManager.conf. - - `none`: NetworkManager will not manage the transient - hostname and will never set it. - -
`dns`	- Set the DNS processing mode. - If the key is unspecified, `default` is used, - unless `/etc/resolv.conf` is a symlink to - `/run/systemd/resolve/stub-resolv.conf`, - `/run/systemd/resolve/resolv.conf`, - `/lib/systemd/resolv.conf` or - `/usr/lib/systemd/resolv.conf`. - In that case, `systemd-resolved` is chosen automatically. - - `default`: NetworkManager will update - `/etc/resolv.conf` to reflect the nameservers - provided by currently active connections. The `rc-manager` - setting (below) controls how this is done. - `dnsmasq`: NetworkManager will run - dnsmasq as a local caching nameserver, using "Conditional Forwarding" - if you are connected to a VPN, and then update - `resolv.conf` to point to the local - nameserver. It is possible to pass custom options to the - dnsmasq instance by adding them to files in the - "`/etc/NetworkManager/dnsmasq.d/`" - directory. Note that when multiple upstream servers are - available, dnsmasq will initially contact them in parallel and - then use the fastest to respond, probing again other servers - after some time. This behavior can be modified passing the - 'all-servers' or 'strict-order' options to dnsmasq (see the - manual page for more details). - `systemd-resolved`: NetworkManager will - push the DNS configuration to systemd-resolved - `none`: NetworkManager will not - modify resolv.conf. This implies - `rc-manager` `unmanaged` - Note that the plugins `dnsmasq` and `systemd-resolved` - are caching local nameservers. - Hence, when NetworkManager writes `/run/NetworkManager/resolv.conf` - and `/etc/resolv.conf` (according to `rc-manager` - setting below), the name server there will be localhost only. - NetworkManager also writes a file `/run/NetworkManager/no-stub-resolv.conf` - that contains the original name servers pushed to the DNS plugin. - When using `dnsmasq` and `systemd-resolved`, - per-connection added dns servers will always be queried using - the device the connection has been activated on. -
`rc-manager`	- Set the `resolv.conf` - management mode. This option is about how NetworkManager writes to - `/etc/resolv.conf`, if at all. - The default value depends on NetworkManager build - options, and this version of NetworkManager was build with a default of - "`auto`". - Regardless of this setting, NetworkManager will - always write its version of resolv.conf to its runtime state directory - as `/run/NetworkManager/resolv.conf`. - - If you configure `dns=none` or make `/etc/resolv.conf` - immutable with `chattr +i`, NetworkManager will ignore this setting and - always choose `unmanaged` (below). - - `auto`: if systemd-resolved plugin is configured via - the `dns` setting or if it gets detected as main DNS plugin, - NetworkManager will update systemd-resolved without touching `/etc/resolv.conf`. - Alternatively, if `resolvconf` or `netconfig` are enabled - at compile time and the respective binary is found, NetworkManager will automatically use it. - Note that if you install or uninstall these binaries, you need to reload the - `rc-manager` setting with SIGHUP or - `systemctl reload NetworkManager`. As last fallback - it uses the `symlink` option (see next). - - `symlink`: If `/etc/resolv.conf` is - a regular file or does not exist, NetworkManager will write the file directly. - If `/etc/resolv.conf` is instead a symlink, NetworkManager - will leave it alone. Unless the symlink points to the internal file - `/run/NetworkManager/resolv.conf`, - in which case the symlink will be updated to emit an inotify notification. - This allows the user to conveniently instruct NetworkManager not - to manage `/etc/resolv.conf` by replacing it with - a symlink. - - `file`: NetworkManager will write - `/etc/resolv.conf` as regular file. If it finds - a symlink to an existing target, it will follow the symlink and - update the target instead. In no case will an existing symlink - be replaced by a file. Note that older versions of NetworkManager - behaved differently and would replace dangling symlinks with a - plain file. - - `resolvconf`: NetworkManager will run - resolvconf to update the DNS configuration. - `netconfig`: NetworkManager will run - netconfig to update the DNS configuration. - `unmanaged`: don't touch - `/etc/resolv.conf`. - `none`: deprecated alias for - `symlink`. -
`systemd-resolved`	- Additionally, send the connection DNS configuration to - `systemd-resolved`. Defaults to "`true`". - - Note that this setting has no effect if the main `dns` - plugin is already `systemd-resolved`. It is complementary to the - `dns` setting to configure systemd-resolved alongside the - main plugin. - If systemd-resolved is enabled, either via this setting or the main - DNS plugin, the connectivity check resolves the - hostname per-device. -
`debug`	- Comma separated list of options to aid - debugging. This value will be combined with the environment - variable `NM_DEBUG`. Currently, the following - values are supported: - - `RLIMIT_CORE`: set ulimit -c unlimited - to write out core dumps. Beware, that a core dump can contain - sensitive information such as passwords or configuration settings. - - - `fatal-warnings`: set g_log_set_always_fatal() - to core dump on warning messages from glib. This is equivalent - to the --g-fatal-warnings command line option. - -
`autoconnect-retries-default`	- The number of times a connection activation should be - automatically tried before switching to another one. This - value applies only to connections that can auto-connect - and have a - `connection.autoconnect-retries` property - set to -1. If not specified, connections will be tried 4 - times. Setting this value to 1 means to try activation once, - without retry. -
`firewall-backend`	- The firewall backend for configuring masquerading - with shared mode. - Set to either `iptables`, `nftables` - or `none`. - `iptables` and `nftables` - require `iptables` and `nft` - application, respectively. - `none` means to skip firewall configuration if - the users wish to manage firewall themselves. - If unspecified, it will be auto detected. -
`iwd-config-path`	- - If the value is "auto" (the default), IWD is queried for its - current state directory when it appears on D-Bus -- the - directory where IWD keeps its network configuration files -- - usually /var/lib/iwd. NetworkManager will then attempt to - write copies of new or modified Wi-Fi connection profiles, - converted into the IWD format, into this directory thus making - IWD connection properties editable. NM will overwrite existing - files without preserving their contents. - - - The path can also be overridden by pointing to a specific - existing and writable directory. On the other hand setting - this to an empty string or any other value disables the - profile conversion mechanism. - - - This mechanism allows editing connection profile settings such - as the 802.1x configuration using NetworkManager clients. - Without it such changes have no effect in IWD. - -
`migrate-ifcfg-rh`	Whether NetworkManager tries to automatically convert - any connection profile stored in ifcfg-rh format to the keyfile format. - Support for ifcfg-rh is deprecated and will be eventually removed. If - enabled, the migration is performed at every startup of the daemon. - The default value is `false`. -

-

-`keyfile` section

-

This section contains keyfile-plugin-specific options, and - is normally only used when you are not using any other - distro-specific plugin.

-

---- - - - - - - - - - - - - - - - - - - -

`hostname`	This key is deprecated and has no effect - since the hostname is now stored in `/etc/hostname` - or other system configuration files according to build options. -
`path`	The location where keyfiles are read and stored. - This defaults to "`/etc/NetworkManager/system-connections`". -
`rename`	- NetworkManager automatically chooses a filename when storing - a new profile to disk. That name depends on the profile's name - (connection.id). When updating a profile's name, the file is - not renamed to not break scripts that rely on the filename - for the profile. - By setting this option to "true", NetworkManager renames - the keyfile on update of the profile, to follow the profile's - name. This defaults to "false". -
`unmanaged-devices`	- Set devices that should be ignored by NetworkManager. - - - A device unmanaged due to this option is strictly - unmanaged and cannot be overruled by using the API like - nmcli device set $IFNAME managed yes. - Also, a device that is unmanaged for other reasons, like - an udev rule, cannot be made managed with this option (e.g. by - using an `except:` specifier). - These two points make it different from the `device*.managed` - option which for that reason may be a better choice. - - See the section called “Device List Format” for the syntax on how to - specify a device. - - - Example: - - -unmanaged-devices=interface-name:em4 -unmanaged-devices=mac:00:22:68:1c:59:b1;mac:00:1E:65:30:D1:C4;interface-name:eth2 - - - -

-

-`ifupdown` section

-

This section contains ifupdown-specific options and thus only - has effect when using the ifupdown plugin.

-

---- - - - - -

managed

-

If set to true, then - interfaces listed in - /etc/network/interfaces are managed by - NetworkManager. If set to false, then - any interface listed in - /etc/network/interfaces will be ignored - by NetworkManager. Remember that NetworkManager controls the - default route, so because the interface is ignored, - NetworkManager may assign the default route to some other - interface.

-

- The default value is false. -

-

-`logging` section

-

- This section controls NetworkManager's logging. - Logging is very important to understand what NetworkManager is doing. - When you report a bug, do not unnecessarily filter or limit the log file. - Just enable level=TRACE and domains=ALL - to collect everything. -

-

- The recommended way for enabling logging is with a file /etc/NetworkManager/conf.d/95-logging.conf - that contains -

-

-[logging]
-level=TRACE
-domains=ALL
-

-

- and restart the daemon with systemctl restart NetworkManager. Then - reproduce the problem. You can find the logs in syslog (for example - journalctl, or journalctl -u NetworkManager - to show only logs from NetworkManager). -

-

- Any settings here are overridden by the --log-level - and --log-domains command-line options. - Logging can also be reconfigured at runtime with - nmcli general logging level "$LEVEL" domains "$DOMAINS". - However, often it is interesting to get a complete log from the - start. Especially, when debugging an issue, enable debug logging - in NetworkManager.conf and restart the service to enable verbose logging - early on. -

-

- By setting nm.debug on the kernel command line (either from - /run/NetworkManager/proc-cmdline or /proc/cmdline), - debug logging is enabled. This overrides both the command-line options and the settings - from NetworkManager.conf. -

-

- NetworkManager's logging aims not to contain private sensitive data - and you should be fine sharing the debug logs. Still, there will - be IP addresses and your network setup, if you consider that private - then review the log before sharing. However, try not to mangle the logfile - in a way that distorts the meaning too much. -

-

- NetworkManager uses syslog or systemd-journald, depending on configuration. - In any case, debug logs are verbose and might be rate limited - or filtered by the logging daemon. For systemd-journald, see - RateLimitIntervalSec and RateLimitBurst - in journald.conf manual for how to disable that. -

-

---- - - - - - - - - - - - - - - - - - - - - - - -

`level`	- The default logging verbosity level. - One of `OFF`, `ERR`, - `WARN`, `INFO`, - `DEBUG`, `TRACE`, - in order of verbosity. - - - `OFF` disables all logging. `INFO` - is the default verbosity for regular operation. `TRACE` - is for debugging. - - - The other levels are in most cases not useful. For example, `DEBUG` - is between `TRACE` and `INFO`, but it's too - verbose for regular operation and lacks possibly interesting messages for debugging. - Almost always, when debugging an issue or reporting a bug, collect full - level `TRACE` logs to get the full picture. - -
`domains`	- Filter the messages by their topic. When debugging - an issue, it's better to collect all logs (`ALL` domain) - upfront. The unnecessary parts can always be ignored - later. - - In the uncommon case to tune out certain topics, the following log - domains are available: - PLATFORM, RFKILL, ETHER, WIFI, BT, MB, DHCP4, DHCP6, PPP, - WIFI_SCAN, IP4, IP6, AUTOIP4, DNS, VPN, SHARING, SUPPLICANT, - AGENTS, SETTINGS, SUSPEND, CORE, DEVICE, OLPC, WIMAX, - INFINIBAND, FIREWALL, ADSL, BOND, VLAN, BRIDGE, DBUS_PROPS, - TEAM, CONCHECK, DCB, DISPATCH, AUDIT, SYSTEMD, VPN_PLUGIN, - PROXY. - In addition, these special domains can be used: NONE, - ALL, DEFAULT, DHCP, IP. - You can specify per-domain log level overrides by - adding a colon and a log level to any domain. E.g., - "`WIFI:DEBUG,WIFI_SCAN:OFF`". - Another example is `ALL,VPN_PLUGIN:TRACE` - to enable all the logging there is (see about `VPN_PLUGIN` - below). - -

`backend`	The logging backend. Supported values - are "`syslog`" and "`journal`". - When NetworkManager is started with "`--debug`" - in addition all messages will be printed to stderr. - If unspecified, the default is "`syslog`". -
`audit`	Whether the audit records are delivered to - auditd, the audit daemon. If `false`, audit - records will be sent only to the NetworkManager logging - system. If set to `true`, they will be also - sent to auditd. The default value is `false`. -

-

-`connection` section

-

Specify default values for connections. -

-

- Such default values are only consulted if the corresponding per-connection property - explicitly allows for that. That means, all these properties correspond to - a property of the connection profile (for example connection.mud-url). - Only if the per-profile property is set to a special value that indicates to use the - default, the default value from NetworkManager.conf is consulted. It depends on the - property, which is the special value that indicates fallback to the default, but it - usually is something like empty, unset values or special numeric values like 0 or -1. - That means the effectively used value can first always be configured for each profile, - and these default values only matter if the per-profile values explicitly indicates - to use the default from NetworkManager.conf. -

-

- Note that while nmcli supports various aliases and convenience features for configuring - properties, the settings in this section do not. For example, enum values usually only - can be configured via their numeric magic number. -

-

- Example: -

-

-[connection]
-ipv6.ip6-privacy=0
-

-

Supported Properties

-

- Not all properties can be overwritten, only the following - properties are supported to have their default values configured - (see nm-settings-nmcli(5) for details). -

-

- - -

-

---- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

`802-1x.auth-timeout`
`cdma.mtu`
`connection.auth-retries`	If left unspecified, the default value is 3 tries before failing the connection. -
`connection.autoconnect-ports`
`connection.autoconnect-slaves`	This is deprecated, please use "connection.autoconnect-ports" instead. -
`connection.down-on-poweroff`	Whether the connection will be brought down before the system is powered off.
`connection.mud-url`	If unspecified, MUD URL defaults to `"none"`.
`connection.lldp`
`connection.llmnr`	If unspecified, the ultimate default values depends on the DNS plugin. With systemd-resolved the default currently is "yes" (2) and for all other plugins "no" (0).
`connection.mdns`	- Currently only the systemd-resolve DNS plugin supports this setting. - If the setting is unspecified both in the profile and in the global - default here, then the default is determined by systemd-resolved. - See `MulticastDNS=` in - resolved.conf(5). -
`connection.mptcp-flags`	If unspecified, the fallback is 0x22 (`"enabled,subflow"`). Note that if sysctl `/proc/sys/net/mptcp/enabled` is disabled, NetworkManager will still not configure endpoints.
`connection.dns-over-tls`	If unspecified, the ultimate default values depends on the DNS plugin. With systemd-resolved the default currently is global setting and for all other plugins "no" (0).
`connection.stable-id`
`ethernet.cloned-mac-address`	If left unspecified, it defaults to "preserve".
`ethernet.generate-mac-address-mask`
`ethernet.mtu`	If configured explicitly to 0, the MTU is not reconfigured during device activation unless it is required due to IPv6 constraints. If left unspecified, a DHCP/IPv6 SLAAC provided value is used or the MTU is not reconfigured during activation.
`ethernet.wake-on-lan`
`gsm.mtu`
`hostname.from-dhcp`
`hostname.from-dns-lookup`
`hostname.only-from-default`
`hostname.priority`
`infiniband.mtu`	If configured explicitly to 0, the MTU is not reconfigured during device activation unless it is required due to IPv6 constraints. If left unspecified, a DHCP/IPv6 SLAAC provided value is used or the MTU is left unspecified on activation.
`ip-tunnel.mtu`	If configured explicitly to 0, the MTU is not reconfigured during device activation unless it is required due to IPv6 constraints. If left unspecified, a DHCP/IPv6 SLAAC provided value is used or a default of 1500.
`ipv4.dad-timeout`
`ipv4.dhcp-client-id`
`ipv4.dhcp-dscp`
`ipv4.dhcp-iaid`	If left unspecified, it defaults to "ifname".
`ipv4.dhcp-hostname-flags`	If left unspecified, the value 3 (fqdn-encoded,fqdn-serv-update) is used.
`ipv4.dhcp-send-release`	Whether the DHCP client will send RELEASE message when bringing the connection down.
`ipv4.dhcp-timeout`	If left unspecified, the default value for - the interface type is used.
`ipv4.dhcp-vendor-class-identifier`	If left unspecified, the default is to not send the DHCP option to the server.
`ipv4.dns-priority`	If unspecified or zero, use 50 for VPN profiles - and 100 for other profiles.
`ipv4.required-timeout`
`ipv4.link-local`	If left unspecified, fallback to "auto" which makes it dependent on "ipv4.method" setting.
`ipv4.route-metric`
`ipv4.route-table`	If left unspecified, routes are only added to the main table. Note that this - is different from explicitly selecting the main table 254, because of how NetworkManager - removes extraneous routes from the tables. -
`ipv6.addr-gen-mode`	If the per-profile setting is either "default" or "default-or-eui64", the - global default is used. If the default is unspecified, the fallback value is either "stable-privacy" - or "eui64", depending on whether the per-profile setting is "default" or "default-or-eui64, respectively.
`ipv6.ra-timeout`	If left unspecified, the default value depends on the sysctl solicitation settings.
`ipv6.dhcp-duid`	If left unspecified, it defaults to "lease".
`ipv6.dhcp-iaid`	If left unspecified, it defaults to "ifname".
`ipv6.dhcp-hostname-flags`	If left unspecified, the value 1 (fqdn-serv-update) is used.
`ipv6.dhcp-send-release`	Whether the DHCP client will send RELEASE message when bringing the connection down.
`ipv6.dhcp-timeout`	If left unspecified, the default value for - the interface type is used.
`ipv6.dns-priority`	If unspecified or zero, use 50 for VPN profiles - and 100 for other profiles.
`ipv6.ip6-privacy`	If `ipv6.ip6-privacy` is unset, use the content of - "/proc/sys/net/ipv6/conf/default/use_tempaddr" as last fallback. -
`ipv6.temp-valid-lifetime`	If `ipv6.temp-valid-lifetime` is unset, use the - content of "/proc/sys/net/ipv6/conf/default/temp_valid_lft" as last fallback. -
`ipv6.temp-preferred-lifetime`	If `ipv6.temp-preferred-lifetime` is unset, use - the content of "/proc/sys/net/ipv6/conf/default/temp_prefered_lft" as last fallback. -
`ipv6.required-timeout`
`ipv6.route-metric`
`ipv6.route-table`	If left unspecified, routes are only added to the main table. Note that this - is different from explicitly selecting the main table 254, because of how NetworkManager - removes extraneous routes from the tables. -
`loopback.mtu`	If configured explicitly to 0, the MTU is not reconfigured during device activation unless it is required due to IPv6 constraints. If left unspecified, a DHCP/IPv6 SLAAC provided value is used or the MTU is left unspecified on activation.
`macsec.offload`
`sriov.autoprobe-drivers`	If left unspecified, drivers are autoprobed when the SR-IOV VF gets created.
`vpn.timeout`	If left unspecified, default value of 60 seconds is used.
`wifi.ap-isolation`	If left unspecified, AP isolation is disabled.
`wifi.cloned-mac-address`	If left unspecified, it defaults to "preserve".
`wifi.generate-mac-address-mask`
`wifi.mac-address-randomization`	If left unspecified, MAC address randomization is disabled. - This setting is deprecated for `wifi.cloned-mac-address`. -
`wifi.mtu`	If configured explicitly to 0, the MTU is not reconfigured during device activation unless it is required due to IPv6 constraints. If left unspecified, a DHCP/IPv6 SLAAC provided value is used or a default of 1500.
`wifi.powersave`	If left unspecified, the default value - "`ignore`" will be used.
`wifi-sec.pmf`	If left unspecified, the default value - "`optional`" will be used.
`wifi-sec.fils`	If left unspecified, the default value - "`optional`" will be used.
`wifi.wake-on-wlan`
`wireguard.mtu`

-

- - -

-

Sections

-

- You can configure multiple connection - sections, by having different sections with a name that all start - with "connection". - Example: -

-

-[connection]
-ipv6.ip6-privacy=0
-connection.autoconnect-ports=1
-vpn.timeout=120
-
-[connection-wifi-wlan0]
-match-device=interface-name:wlan0
-ipv4.route-metric=50
-
-[connection-wifi-other]
-match-device=type:wifi
-ipv4.route-metric=55
-ipv6.ip6-privacy=1
-

-

- The sections within one file are considered in order of appearance, with the - exception that the [connection] section is always - considered last. In the example above, this order is [connection-wifi-wlan0], - [connection-wlan-other], and [connection]. - When checking for a default configuration value, the sections are searched until - the requested value is found. - In the example above, "ipv4.route-metric" for wlan0 interface is set to 50, - and for all other Wi-Fi typed interfaces to 55. Also, Wi-Fi devices would have - IPv6 private addresses enabled by default, but other devices would have it disabled. - Note that also "wlan0" gets "ipv6.ip6-privacy=1", because although the section - "[connection-wifi-wlan0]" matches the device, it does not contain that property - and the search continues. -

-

- When having different sections in multiple files, sections from files that are read - later have higher priority. So within one file the priority of the sections is - top-to-bottom. Across multiple files later definitions take precedence. -

-

- The following properties further control how a connection section applies. -

-

---- - - - - - - - - - - -

match-device

An optional device spec that restricts - when the section applies. See the section called “Device List Format” - for the possible values. -

stop-match

An optional boolean value which defaults to - no. If the section matches (based on - match-device), further sections will not be - considered even if the property in question is not present. In - the example above, if [connection-wifi-wlan0] would - have stop-match set to yes, - the device wlan0 would have ipv6.ip6-privacy - property unspecified. That is, the search for the property would not continue - in the connection sections [connection-wifi-other] - or [connection]. -

-

-`device` section

-

Contains per-device persistent configuration. -

-

- Example: -

-

-[device]
-match-device=interface-name:eth3
-managed=1
-

-

Supported Properties

-

- The following properties can be configured per-device. -

-

---- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

`managed`	- Whether the device is managed or not. A device can be - marked as managed via udev rules (ENV{NM_UNMANAGED}), - or via setting plugins (keyfile.unmanaged-devices). - This is yet another way. Note that this configuration - can be overruled at runtime via D-Bus. Also, it has - higher priority then udev rules. -
`carrier-wait-timeout`	- - Specify the timeout for waiting for carrier in milliseconds. - The default is 6000 milliseconds. - This setting exists because certain drivers/hardware can take - a long time to detect whether the cable is plugged in. - - - When the device loses carrier, NetworkManager does not react - immediately. Instead, it waits for this timeout before considering - the link lost. - - - Also, on startup, NetworkManager considers the - device as busy for this time, as long as the device has no carrier. - This delays startup-complete signal and NetworkManager-wait-online. - Configuring this too high means to block NetworkManager-wait-online - longer than necessary when booting with cable unplugged. Configuring - it too low, means that NetworkManager will declare startup-complete too - soon, although carrier is about to come and auto-activation to kick in. - Note that if a profile only has static IP configuration or Layer 3 configuration - disabled, then it can already autoconnect without carrier on the device. - Once such a profile reaches full activated state, startup-complete - is considered as reached even if the device has no carrier yet. - -
`ignore-carrier`	- - Specify devices for which NetworkManager will (partially) - ignore the carrier state. Normally, for - device types that support carrier-detect, such as Ethernet - and InfiniBand, NetworkManager will only allow a - connection to be activated on the device if carrier is - present (ie, a cable is plugged in), and it will - deactivate the device if carrier drops for more than a few - seconds. - - - A device with carrier ignored will allow activating connections on - that device even when it does not have carrier, provided - that the connection uses only statically-configured IP - addresses. Additionally, it will allow any active - connection (whether static or dynamic) to remain active on - the device when carrier is lost. - - - Note that the "carrier" property of NMDevices and device D-Bus - interfaces will still reflect the actual device state; it's just - that NetworkManager will not make use of that information. - - - Master types like bond, bridge and team ignore carrier by default, - while other device types react on carrier changes by default. - - - This setting overwrites the deprecated `main.ignore-carrier` - setting above. - -
`keep-configuration`	- - On startup, NetworkManager tries to not interfere with - interfaces that are already configured. It does so by - generating a in-memory connection based on the interface - current configuration. - - - If this generated connection matches one of the existing - persistent connections, the persistent connection gets - activated. If there is no match, the generated - connection gets activated as "external", which means - that the connection is considered as active, but - NetworkManager doesn't actually touch the interface. - - - It is possible to disable this behavior by setting - `keep-configuration` to - `no`. In this way, on startup - NetworkManager always tries to activate the most - suitable persistent connection (the one with highest - autoconnect-priority or, in case of a tie, the one - activated most recently). - - - Note that when NetworkManager gets restarted, it stores - the previous state in - `/run/NetworkManager`; in particular - it saves the UUID of the connection that was previously - active so that it can be activated again after the - restart. Therefore, - `keep-configuration` does not have - any effect on service restart. - -
`allowed-connections`	- - A list of connections that can be activated on the - device. See the section called “Connection List Format” for the - syntax to specify a connection. If this option is not - specified, all connections can be potentially activated - on the device, provided that the connection type and - other settings match. - - - A notable use case for this is to filter which - connections can be activated based on how they were - created; see the `origin` keyword in - the section called “Connection List Format”. - -
`wifi.scan-rand-mac-address`	- Configures MAC address randomization of a Wi-Fi device during - scanning. This defaults to `yes` in which case - a random, locally-administered MAC address will be used. - The setting `wifi.scan-generate-mac-address-mask` - allows to influence the generated MAC address to use certain vendor - OUIs. - If disabled, the MAC address during scanning is left unchanged to - whatever is configured. - For the configured MAC address while the device is associated, see instead - the per-connection setting `wifi.cloned-mac-address`. -
`wifi.backend`	- Specify the Wi-Fi backend used for the device. Currently, supported - are `wpa_supplicant` and `iwd` (experimental). - If unspecified, the default is "`wpa_supplicant`". -
`wifi.scan-generate-mac-address-mask`	- Like the per-connection settings `ethernet.generate-mac-address-mask` - and `wifi.generate-mac-address-mask`, this allows to configure the - generated MAC addresses during scanning. See nm-settings-nmcli(5) - for details. -
`wifi.iwd.autoconnect`	- If `wifi.backend` is `iwd`, setting this to - `false` forces IWD's autoconnect mechanism to be disabled for - this device and connections will only be initiated by NetworkManager whether - commanded by a client or automatically. Leaving it `true` (default) - stops NetworkManager from automatically initiating connections and allows - IWD to use its network ranking and scanning logic to decide the best networks - to autoconnect to next. Connections' `autoconnect-priority`, - `autoconnect-retries` settings will be ignored. Other settings - like `permissions` or `multi-connect` may interfere - with IWD connection attempts. -
`sriov-num-vfs`	- Specify the number of virtual functions (VF) to enable - for a PCI physical device that supports single-root I/O - virtualization (SR-IOV). -

-

Sections

-

- The [device] section works the same as the [connection] section. - That is, multiple sections that all start with the prefix "device" can be specified. - The settings "match-device" and "stop-match" are available to match a device section - on a device. The order of multiple sections is also top-down within the file and - later files overwrite previous settings. See “Sections” under the section called “CONNECTION SECTION” - for details. -

-

-`connectivity` section

-

This section controls NetworkManager's optional connectivity - checking functionality. This allows NetworkManager to detect - whether or not the system can actually access the internet or - whether it is behind a captive portal.

-

Connectivity checking serves two purposes. For one, it exposes - a connectivity state on D-Bus, which other applications may use. For example, - Gnome's portal helper uses this as signal to show a captive portal login - page. - The other use is that default-route of devices without global connectivity - get a penalty of +20000 to the route-metric. This has the purpose to give a - better default-route to devices that have global connectivity. For example, - when being connected to WWAN and to a Wi-Fi network which is behind a captive - portal, WWAN still gets preferred until login.

-

Note that your distribution might set /proc/sys/net/ipv4/conf/*/rp_filter to - strict filtering. That works badly with per-device connectivity checking, - which uses SO_BINDDEVICE to send requests on all devices. A strict rp_filter - setting will reject any response and the connectivity check on all but the - best route will fail.

-

---- - - - - - - - - - - - - - - - - - - - - - - -

`enabled`	Whether connectivity check is enabled. - Note that to enable connectivity check, a valid uri must - also be configured. The value defaults to true, but since - the uri is unset by default, connectivity check may be disabled. - The main purpose of this option is to have a single flag - to disable connectivity check. Note that this setting can - also be set via D-Bus API at runtime. In that case, the value gets - stored in `/var/lib/NetworkManager/NetworkManager-intern.conf` - file. -
`uri`	The URI of a web page to periodically - request when connectivity is being checked. This page - should return the header "X-NetworkManager-Status" with a - value of "online". Alternatively, its body content should - be set to "NetworkManager is online". The body content - check can be controlled by the `response` - option. If this option is blank or missing, connectivity - checking is disabled. -
`interval`	Specified in seconds; controls how often - connectivity is checked when a network connection exists. If - set to 0 connectivity checking is disabled. If missing, the - default is 300 seconds.
`timeout`	Specified in seconds; controls how long - to wait for a response before connectivity is marked as - limited. If missing, the default is 20 seconds.
`response`	If set, controls what body content - NetworkManager checks for when requesting the URI for - connectivity checking. Note that this only compares - that the HTTP response starts with the specifid text, - it does not compare the exact string. This behavior - might change in the future, so avoid relying on it. - If missing, the response defaults to "NetworkManager is online". - If set to empty, the HTTP server is expected to answer with - status code 204 or send no data.

-

-`global-dns` section

-

This section specifies DNS settings that are applied - globally, in addition to connection-specific ones.

-

---- - - - - - - - - - - -

`searches`	- A list of search domains to be used during hostname lookup. -
`options`	- A list of options to be passed to the hostname resolver. -

-

-`global-dns-domain` sections

-

Sections with a name starting with the "global-dns-domain-" - prefix allow to define global DNS configuration for specific - domains. The part of section name after "global-dns-domain-" - specifies the domain name a section applies to (for example, a - section could be named "global-dns-domain-foobar.com"). More - specific domains have the precedence over less specific ones and - the default domain is represented by the wildcard "*". - - To be valid, global DNS domains must include a section for the - default domain "*". When the global DNS domains are valid, the - name servers and domains defined globally override the ones from - active connections. -

-

---- - - - - - - - - - - -

`servers`	- A list of addresses of DNS servers to be used for the given domain. -
`options`	- A list of domain-specific DNS options. Not used at the moment. -

-

-`.config` sections

-

This is a special section that contains options which apply - to the configuration file that contains the option. -

-

---- - - - - -

enable

-

- Defaults to "true". If "false", - the configuration file will be skipped during loading. - Note that the main configuration file NetworkManager.conf - cannot be disabled. -

-

-# always skip loading the config file
-[.config]
-enable=false
-

-

- You can also match against the version of NetworkManager. For example - the following are valid configurations: -

-

-# only load on version 1.0.6
-[.config]
-enable=nm-version:1.0.6
-
-# load on all versions 1.0.x, but not 1.2.x
-[.config]
-enable=nm-version:1.0
-
-# only load on versions >= 1.1.6. This does not match
-# with version 1.2.0 or 1.4.4. Only the last digit is considered.
-[.config]
-enable=nm-version-min:1.1.6
-
-# only load on versions >= 1.2. Contrary to the previous
-# example, this also matches with 1.2.0, 1.2.10, 1.4.4, etc.
-[.config]
-enable=nm-version-min:1.2
-
-# Match against the maximum allowed version. The example matches
-# versions 1.2.0, 1.2.2, 1.2.4. Again, only the last version digit
-# is allowed to be smaller. So this would not match on 1.1.10.
-[.config]
-enable=nm-version-max:1.2.6
-

-

- You can also match against the value of the environment variable - NM_CONFIG_ENABLE_TAG, like: -

-

-# only load the file when running NetworkManager with
-# environment variable "NM_CONFIG_ENABLE_TAG=TAG1"
-[.config]
-enable=env:TAG1
-

-

- More then one match can be specified. The configuration will be - enabled if one of the predicates matches ("or"). The special prefix "except:" can - be used to negate the match. Note that if one except-predicate - matches, the entire configuration will be disabled. - In other words, a except predicate always wins over other predicates. - If the setting only consists of "except:" matches and none of the - negative conditions are satisfied, the configuration is still enabled. -

-

-# enable the configuration either when the environment variable
-# is present or the version is at least 1.2.0.
-[.config]
-enable=env:TAG2,nm-version-min:1.2
-
-# enable the configuration for version >= 1.2.0, but disable
-# it when the environment variable is set to "TAG3"
-[.config]
-enable=except:env:TAG3,nm-version-min:1.2
-
-# enable the configuration on >= 1.3, >= 1.2.6, and >= 1.0.16.
-# Useful if a certain feature is only present since those releases.
-[.config]
-enable=nm-version-min:1.3,nm-version-min:1.2.6,nm-version-min:1.0.16
-

-

Plugins

-

- Settings plugins for reading and writing connection profiles. The number of - available plugins is distribution specific. -

-

---- - - - - - - - - - - - - - - - - - - - - - - -

`keyfile`	- - The `keyfile` plugin is the generic - plugin that supports all the connection types and - capabilities that NetworkManager has. It writes files out - in an .ini-style format in - `/etc/NetworkManager/system-connections`. - See nm-settings-keyfile(5) - for details about the file format. - - - The stored connection file may contain passwords, secrets and - private keys in plain text, so it will be made readable only to - root, and the plugin will ignore files that are readable or - writable by any user or group other than root. See "Secret flag types" - in nm-settings-nmcli(5) - for how to avoid storing passwords in plain text. - - - This plugin is always active, and will automatically be - used to store any connections that aren't supported by any - other active plugin. - -
`ifcfg-rh`	- This plugin is now deprecated; it can be used on the - Fedora and Red Hat Enterprise Linux distributions to read - and write configuration from the standard - `/etc/sysconfig/network-scripts/ifcfg-*` - files. It currently supports reading Ethernet, Wi-Fi, - InfiniBand, VLAN, Bond, Bridge, and Team connections. - Enabling `ifcfg-rh` implicitly enables - `ibft` plugin, if it is available. - This can be disabled by adding `no-ibft`. - See `/usr/share/doc/initscripts/sysconfig.txt` - and nm-settings-ifcfg-rh(5) - for more information about the ifcfg file format. -
`ifupdown`	- - This plugin is used on the Debian and Ubuntu - distributions, and reads Ethernet and Wi-Fi connections - from `/etc/network/interfaces`. - - - This plugin is read-only; any connections (of any type) - added from within NetworkManager when you are using this - plugin will be saved using the `keyfile` - plugin instead. - -
`ibft`, `no-ibft`	- These plugins are deprecated and their selection has no effect. - This is now handled by nm-initrd-generator. -
`ifcfg-suse`, `ifnet`	- These plugins are deprecated and their selection has no effect. - The `keyfile` plugin should be used - instead. -

-

Appendix

-

Device List Format

-

- The configuration options main.no-auto-default, main.ignore-carrier, - keyfile.unmanaged-devices, connection*.match-device and - device*.match-device select devices based on a list of matchings. - Devices can be specified using the following format: -

-

---- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

*	Matches every device.
IFNAME	Case sensitive match of interface name of the device. Globbing is not supported.
HWADDR	Match the permanent MAC address of the device. Globbing is not supported
interface-name:IFNAME, interface-name:~IFNAME	Case sensitive match of interface name of the device. Simple globbing is supported with - `*` and `?`. Ranges and escaping is not supported.
interface-name:=IFNAME	Case sensitive match of interface name of the device. Globbing is disabled and `IFNAME` - is taken literally.
mac:HWADDR	Match the permanent MAC address of the device. Globbing is not supported
s390-subchannels:HWADDR	Match the device based on the subchannel address. Globbing is not supported
type:TYPE	Match the device type. Valid type names are as reported by "`nmcli -f GENERAL.TYPE device show`". - Globbing is not supported.
driver:DRIVER	Match the device driver as reported by "`nmcli -f GENERAL.DRIVER,GENERAL.DRIVER-VERSION device show`". - "`DRIVER`" must match the driver name exactly and does not support globbing. - Optionally, a driver version may be specified separated by '/'. Globbing is supported for the version. -
dhcp-plugin:DHCP	Match the configured DHCP plugin "`main.dhcp`". -
except:SPEC	- Negative match of a device. `SPEC` must be explicitly qualified with - a prefix such as `interface-name:`. A negative match has higher priority then the positive - matches above. - If there is a list consisting only of negative matches, the behavior is the same as if there - is also match-all. That means, if none of all the negative matches is satisfied, the overall result is - still a positive match. That means, `"except:interface-name:eth0"` is the same as - `"*,except:interface-name:eth0"`. -
SPEC[,;]SPEC	- Multiple specs can be concatenated with commas or semicolons. The order does not matter as - matches are either inclusive or negative (`except:`), with negative matches having higher - priority. - - Backslash is supported to escape the separators ';' and ',', and to express special - characters such as newline ('\n'), tabulator ('\t'), whitespace ('\s') and backslash ('\\'). The globbing of - interface names cannot be escaped. Whitespace is not a separator but will be trimmed between - two specs (unless escaped as '\s'). - -

-

- Example: -

-

-interface-name:em4
-mac:00:22:68:1c:59:b1;mac:00:1E:65:30:D1:C4;interface-name:eth2
-interface-name:vboxnet*,except:interface-name:vboxnet2
-*,except:mac:00:22:68:1c:59:b1
-

-

Connection List Format

-

- Connections can be specified using the following format: -

-

---- - - - - - - - - - - - - - - - - - - - - - - - - - - -

*	Matches every connection.
uuid:UUID	Match the connection by UUID, for example - `"uuid:83037490-1d17-4986-a397-01f1db3a7fc2"`
id=ID	Match the connection by name.
origin:ORIGIN	Match the connection by origin, stored in the - `org.freedesktop.NetworkManager.origin` tag of the user setting. For example, use - `"except:origin:nm-initrd-generator"` to forbid activation of connections created by the - initrd generator.
except:SPEC	- Negative match of a connection. A negative match has higher priority then the positive - matches above. - If there is a list consisting only of negative matches, the behavior is the same as if there is also - match-all. That means, if none of all the negative matches is satisfied, the overall result is still a - positive match. -
SPEC[,;]SPEC	- Multiple specs can be concatenated with commas or semicolons. The order does not matter as - matches are either inclusive or negative (`except:`), with negative matches having higher - priority. - Backslash is supported to escape the separators ';' and ',', and to express special characters such as - newline ('\n'), tabulator ('\t'), whitespace ('\s') and backslash ('\\'). Whitespace is not a separator but - will be trimmed between two specs (unless escaped as '\s'). -

-